Magnetic Bit Holder for Milwaukee M12 Impact Driver & Drill - Milwaukee Bit Holder for M12

The media could not be loaded. So far very stoked on this bit holder/magnet! Actually quite impressed with the magnets. They are even holding the double sided bits quite well which I like to keep on my M12 as it's my go to for quick fixes that I leave in my truck at all times. You can see in the video I can't even shake them out despite not having a full hex head contacting the magnets. I also love the side magnet I put about a dozen 1.5" deck screws on there while disassembling something and didn't lose one! It's quite low profile and hasn't really gotten in the way at all. Time will tell how well it holds up but so far I gotta give it five stars.One note below about an issue that may or may not be resolved yet between Amazon and the seller.I had a bit of trouble getting the right model for my Gen3 M12 impact driver due some issues with Amazon mis labeling some of the stock. Just be careful if you order the BLACK Gen3 M12 for RIGHT side you may get the wrong one instead you may get the one for Gen2 which won't work on a Gen3 driver. I went back and forth with Amazon doing a return and getting the wrong one again despite sending a message to make sure they sent the Gen3. After this they promised me it would be ok, it's fixed, go ahead and order again. Well again it was the wrong one sent. I returned the third one and had given up, but then got to talk to Simon the owner, and he straightened everything out for me. I ended up going with the Red which was not having issues with fulfillment and I'm actually really pleased with how well it matches the red driver.

I've had it on my gun for over a week now as a mobile tech for ford. It has held up to multiple drops and retained the bits i had in the holders. The magnets hold small screws well even while using the impact. Its a great addition to the impact for the price and was very simple to install using the factory clips mounting holes.

Ordered this to hold my most frequent bits on my travel impact and drill set. Fit and finish is great. When I first installed it i thought the front being offset mort than the rear was strange but it turned out to be really useful. Made it so large bits could easily fit, which the wouldn't have if they were close like the rear small bit holders. Haven't had any retention issues. Liked it enough to order a second one for my drill.

Simple yet extremely convenient. I’d buy it again and again. The first time I bought one a while back it didn’t last long and broke but the quality seems to have improved since then because the last one I bought is more sturdy and is lasting much longer. Worth the price for sure.

Way too expensive, but super useful and well made. Magnets ate good and it's made fro. Decent plastic and is molded well. Use it all the time. 4 stars cuz of the cost.

Firstly, I've bought four of these and have them on three of my m12 drill/impacts. They are amazing, and my favorite bit attached bit holder, they are a joy to use, great design and well made.....mostly.I've put them on, taken them off, swapped them several times, lots of experience with them. Recently I had to replace my M12 impact and drill, so I purchased another 2 pack of the simon bit holders to install. Unfortunately as I was installing the holder on my impact the screw broke, leaving the post in the threaded insert. I hadn't even got the screw seated, it was not overtightened. Keep in mind the supplied screws have a dab of threadlock on them, which is great, if the screw stays in one piece.I tried to get a grip on it with a small set of pliers to back it out but there just wasn't enough sticking out. Next I tried screw extractors, again couldn't get a good bite on it. Tried to carefully drill out the post, but at last nothing worked. This is a BRAND NEW impact, I pulled it out of the box moments before installing the also brand new bit holder. I have others that are over a year old and have been on and off several times. Not sure if they are using different screws now or it could very well just be a bad one. Either way I now have a brand new impact with a ruined attachment point, didn't even get to use it yet. Super disappointing.BEWARE! Don't ruin your tools.I would like to message the seller directly but cant find their contact info. Hopefully it was just one bad screw.

We love our bit holders. I put them on all of our M12 Surge impact drivers. Keeps all of the common bits handy. Note.....you must use short bits on the back side. Otherwise, great accessory.

Lo único que le critico a este producto es que es muy costoso pero una vez instalado cumple su función y la calidad es óptima, cumple con retener las puntas de destornillador dentro de los agujeros del soporte magnéticamente y la verdad después de agitar intensamente el atornillador de impacto no se cae ninguna. Muy buena compra. Altamente recomendable.