DOME GLASSWhitestone GEN Film Screen Protector for Samsung Galaxy Z Fold 3 (2021) Anti-Bubble HD Clear Hard Coated PET Film Screen Guard

Honestly the screen protector is really good. It feels better than the original screen protector and was fairly simple to install. My only complaint is that the instructions really exaggerate how simple removing the original screen protector cab be. The way it sits under the frame can be really difficult to get to and I could see how it could be easy to damage the inner screen itself during removal. Also the screen protector leaves behind a severe amount of residue. The single alcohol pad that was included in the kit was not nearly enough to remove all the remaining adhesive on the screen. So if you are going to install this yourself buy a high quality microfiber cloth, compressed air, and a flashlight. To remove the inner screen protector I would recommend starting from the middle using a plastic pry tool or a guitar pick if you have. You have to gently pry up til you see a bubble forming. Once you see that bubble forming make sure to turn on the screen to ensure you aren't below the oled screen. Once you confirm you are above the oled work back and forth from left to right to expand the bubble. One you can grab gently start to peel it away while using your free hand to hold the phone in place. Once fully removed use some rubbing alcohol (preferably 90% or higher) and the included micro fiber cloth to remove the old adhesive. Then use your personal micro fiber cloth to clean the screen. Use a flash light directly above the screen while sitting away to ensure dust does not fall onto the screen. Use the compressed air to blow off all the dust and particles and use the included dust remover to get rid of any hard to remove pieces of dust. After ensuing it's fully clear follow the remaining instructions in the video to apply the screen. Make sure to follow it exactly as they do. Including putting pressure on each side while removing the mounting holes. After removing the outer plastic make sure to use the smaller side of the spudger to push out any remaining air bubbles. Then make sure to let it sit open for 15 min for the adhesive to fully stick. Then fold and open your phone a few times to ensure no bubbles have formed. If following these steps exactly you should have a perfectly seated screen protector with no bubbles or dust. I'll attach a photo of mine later to show how I will look when done properly.

Was easy to apply with supplied template. Happy with the product as I have tried several of the other products. Started about 2 weeks later a bubble appeared. Today the whole middle where the screen folds is all lifted up. Created an account on Whitestone website. Registered product and tried to warranty it. Go through the process and they want to charge $9.99 for a replacement. No, Thanks! Their product failed and they want to charge me more for a replacement?.!?!?!

I liked the idea of having the jig in order to easily place the screen protector. I skimmed the video and ordered the screen protector.Everything went fine until the end. It looked like the top and bottom of the plastic was supposed to tear off to leave the screen protector. I managed to do this with a little folding of the plastic. It left the edges a bit rough but manageable. After opening and closing a few times the screen protector pulled away from the screen and I had to keep pushing it back in place. After a few days it looked horrible. I ordered something else to try instead.Funny thing. I removed the screen protector and noticed that the real screen protector was on the phone still. I skipped the part that the plastic on the screen protector was supposed to come off. The whole time the real one was on the phone doing its job lol.It looks great and is a perfect fit. I seen some other bad reviews and I think they probably did the same thing as me and left the removable plastic on the phone instead of removing like the video shows.Knowing this I give it 5 stars for how easy it was to install and the quality.

So my screen protector that came with the phone started getting bubbles on the crease at the very top and bottom and over the course of a week the bubbles got larger and larger till they went down the entire crease. Knowing there was no going back, I just peeled it off and admired the bare screen and the added clarity. Rocked it nude for a few days as I researched good screen protector replacements on reddit and google. Low and behold this is the one I found that had good reviews.This protector unlike the other cheap junk on Amazon actually comes with a bunch of tools and a jig to basically idiot proof the installation (not idiot proof enough it seems looking at the reviews lol). But I REALLY recommend watching the installation video - either here or on Youtube where it’s a higher resolution video.It took me a few days to muster the courage to install it onto my nude fold 3 inner-screen but I decided to go for it. Loaded up the video, followed the video step by step and occasionally paused and in under 5 minutes I had it installed.I couldn’t believe how good it looked and how precisely it went on (Thanks Whitestone Dome engineering team <3) it looks like a brand-new OEM installed protector. I’ve open and closed it a hundred times and it’s not lifting in the middle or anywhere else.I then ran to my wife like an excited little schoolboy to show her my work (she also has a fold 3) and bragged to friends with folds.This protector seems too good to be true, but it’s not. As long as you follow the video guide step by step and don’t rush steps you’ll be golden.I am SO GLAD I didn’t have to send this into Samsung to do it and been without my phone for weeks.There’s a few tiny bubbles on the left side, but they are the sort that disappear after a day or so (I hope) there’s no debris under them so shouild be fine.Will update this review at some point in the future if it fails or whatever :)