Tiertime UP Fila Premium PLA 3D Printer Filament, Low Odor, Consistent 1.75mm Diameter,1KG (500g×2 Spools), Burgundy Red C-22-09

BURGUNDYThis is one of my favorite PLA filaments from Tiertime. The deep candy color and surface sheen makes prints look terrific, especially when printing objects with curved surfaces, like a vase. This filament prints reliably, too; I’ve printed quite a few spools of the stuff without incident. One caveat though – because of the surface sheen, you can’t sand out just a small area, because any scratches are immediately obvious. You can however, sand the entire part smooth (up to 320-400 grit), which produces an attractive, more opaque dull luster. I’ve been using Tiertime printers for five years, starting with the original UpMini, which was programmed only for Tiertime PLA and ABS, and it worked flawlessly with those filaments, and badly with other filaments I tried. I have an UpBox+ now, and although UpStudio lets me tweak settings to print with other materials, for PLA, the Fila filaments and stock settings are still my go-to choice. They come packed two 500g spools per box; each spool was individually vacuum-packed, so one spool stays factory-sealed until needed.GREYThis is my favorite Fila filament for two reasons. It prints extremely well, usually requiring little, if any, post processing. And if sanding is needed, unlike many other plastics, when sanded, the surface doesn’t change color or reflectivity, so sanding scratches are much less obvious, which means you don’t have to sand to as fine a grit to get a nice-looking surface. Take note: Tiertime calls the color Grey, but it’s actually a very light grey, more like eggshell; the online images at the Tiertime Amazon store show the colors pretty accurately, so you can see what I mean. This is my most-used filament for prototyping; it has a soft, yet almost stone-like feel.

In general I get good product from Up Fila material. Not the case with the Tiertime low odor premium PLA Filament, Grey, 1KG. Because I need various colors for various projects and clients, I bought multiple colors back in Nov. 2017. I just opened the grey today, 8-27-18. Each time I try to print the material breaks every 14 - 18 inches into the model.The material is old or defective mix... I don't know? I've tried to contact the supplier but can't find their information. I'm hoping they'll replace the material. Even more, I'm hoping the other material that I purchased won't have the same problems!!!

The product looks really nice but after 45 min to 1 hour of printing it get stuck on the nozzle. I bought it for my new UP Mini 2 ES. Printed ABS without any problems and excellent results.

Seller listed as 1kg and it was two 500g spools of filament, I did not see it was two spools and was expecting a single 1kg spool. listing was in the 1kg section and should have been in the 500g section. Just a little misleading.

i ordered a KG of Burgundy PLA. i got a KG of Green ABS. Both stickers were on the box, but i can't use ABS. :(

I have the Cetus MKII and tried many filaments. This is the one with the best and most predictable results.

Reliable Print, but expensive

Tiertime社のCetus MK III Extendedで使っています。Afinia H400もABSフィラメントで併用しています。こちらはケースもなくベッドも常温ですが、すこしざらっとした表面＆コーティングのおかげか、PLAフィラメントがしっかり食いつき、かつ剥がしやすいです。印刷は細部に少し雑になるところがありますが、Afiniaと比べてもほぼ遜色ない感じです。雑になる原因がプリンタにあるのかフィラメントにあるのかは今のところ不明です。ベッドから印刷物を剥がすとき、DIY店で買った井上工具株式会社のはがしヘラR40mmを使うと面白いように剥がれ、お勧めです。