Koala Printable Clear Sticker Paper - ONLY for LASER Printer - 8.5x11 Inch 20 Sheets Full Sheet 100% Transparent Label Paper for DIY Personalized Decals, Labels

Very good clarity, prints well, no smears, easy to use, worked perfectly with the printer, and sticks well to a variety of surfaces.

I make my own business labels using my laser printer. As long as you put in the correct size or customize the paper settings like I do, then this will print beautifully. It's thick so you'll need the heavy paper setting. It's sticks really well, even when you peel and restock. The price is OK too. Its smooth with no ink smudging and it's dry as soon as it comes out the printer.

These are perfect. Very often you'll get a sticker that you print on only to not be very sticky and then have the stupid thing fall off. These were perfect to do a relabeling project and looked great after. Ink stayed on and didn't flake. Good coloring overall.

Prints perfectly. Ink stays on without smearing. I printed my first sample at home on my Brother Laser printer. Turned out good but my printer was running low on toner, so took it to FedEx Office Print Center and the associate helped me print there on their self service machines. Turned out beautifully. Will order more as needed.

Using a Brother MFC-L8600, set to print on label paper at high quality, printing a single sheet at a time from the multifunction tray, I had the following experience:• The first page jammed. Opening up the back, it had gotten all folded/wrinkled up on itself, like it became ultra-floppy when heated up.• My printer has a pass-through mode for use with envelopes, where you flip a pair of switches and leave the back of the printer open as you print - it avoids the paper making any large turns. I turned that on and printed again; this time it printed without any difficulty. I laid the label sheet flat and put a box along one edge to keep it from curling up and let it cool for a few minutes.• The vast majority of what I printed adhered extremely well. However, some - but not all - areas of solid intense red had adhesion problems, particularly the ones closest to the edges of the page. My layperson's guess is that the solid high-saturation red resulted in lots more toner that needed fusing to the sticker-paper (since it's 100% Magenta + 100% Yellow), and/or that the heat from the fusing drum might be a touch less strong near the edges for some reason. The red stickers still came out OK for my purposes - some were entirely fine, others lost edge details, others had some of the toner in the solid area rub away leaving a much lighter color - but I'm not selling them. Other solid colors didn't have this issue, and the problem was lesser or absent further away from the edge.• Cutting the sheet was easy.• Peeling the sticker off the backing wasn't too bad, but making sure it didn't immediately adhere to my hand was a little trickier.• On the destination surface, the adhesive stuck well, but I could pull off a sticker I'd mis-aligned. (This often but not always resulted in it not looking *quite* as nice on re-application, though not terrible.)• The clear portion is pretty clear - not 100% invisible, when the light's from the right angle it's easy enough to see the edge, but from other angles you just notice the design, and there's not an amber background. I haven't used other clear labels, so can't say 'better/worse' than others, but these ones are definitely at least "satisfactory". (As of use - I don't know if clear labels yellowing with age is a thing that might happen or not.)I'm going to be more careful about areas of solid color and try and keep the amount of toner in those areas lower (by not using 100% saturation, by using hues that don't mix multiple colors of toner, by turning on toner-saver mode) and see how that goes. Other than that one problem and a slightly more involved printing process, these worked great.

I used these sheets to make custom stickers for cocktail stirrers for my upcoming wedding. They printed perfectly. There was no smearing. They dried right away (I was impatient and touched them as soon as they finished printing) and nothing came off. I even got one sheet jammed and the printing was still intact - make sure to change the paper type to a thicker one!!!!. I used my cricut to cut them out after. 100/10 recommend :)Just remember you NEED a LASERJET printer and NEED to change the PAPER TYPE for these to print properly.

This sticker paper works well in my Epson 2850. Dries fast and applies pretty well. It seems to be holding its stickiness on the things I’ve stuck it to as well.

I have a $600 HP Laser printer that is less than 60 days old. I ran ONE sheet of these labels through it, that came out wrinkled in the middle. Now, every piece of paper I print comes out with a wrinkle/crease in the middle and print that looks smeared, as if printed on low-quality inkjet!! I AM NOT HAPPY!!!!