Round Edge Polyhedral Dice - Silicone Mold - 2 Part Hybrid Sprue Mold - FULL SET - For Resin Casting

We've made a couple sets of dice with this mold. It's fairly easy to use, but it can be difficult to get all the bubbles out. The seller's responded quickly when I asked about using a pressure pot, and they recommended 30psi. They also recommended using a toothpick to remove bubbles. The dice are easy to remove after they are set, and the mold is quite durable. I recommend this mold, and would buy it again.

Seeing as I was being lazy instead of casting my own mold, there isn’t much I can complain about. A few of the “runners” are a bit narrow, and while this means they are easier to clean on the final product. However the actual poor cups at the top of the mold are a bit wide. While this defiantly makes posting easier, it means demolding the parts is a bit more destructive to the mold. There is also a lip from where the cup/runner is attached to the dice. This creates a bit of a problem with developing air pockets when pooring that results in a half a dice. But these are in the end minor issues that patience and attention take care off pretty reliably. I also want to add that the product shipped and got to me in like half the expected time.

Very Durable silicone mold but the d12 is disappointing and the pour spouts are massive and will ruin the mold very quickly forcing you to buy another.

I think the only thing I dont like about this mold is that the d12 sprue/spout is set up over the "1", so when you go to cut off the access you have to try to carve it back into the die, which does not match the rest of the fonts.That being said, had a good first experience with the mold. D4 overflowed a bit and caused some shifting but sanding and polishing helped take the nick out a bit. Going to try rubberbanding down the mold on the second attempt.Unlike other molds (especially found on etsy) I like that this comes as one solid block. Helps for less spill and mess clean upEverything aside, the mold is still a blessing to what I could attempt to make at home on my own. Thanks for making a good product.

The resin leaks out the side even when duct tape shut. When I used rubber bands to try to keep it shut it threw off the alignment and so all my dice have the top half off center. Would be a good product if the side didn't leak out half of the resin. Maybe it was a defective mold but it was frustrating spending over $100 for molds that leak and cause an extreme waste of resin.

It's made well, but i think the maker used a warped set of dice to create these molds. I've seen many bad sets before and it's most pronounced on the D6. Likely using Chessex, cheap pretty dice and there is a lot of inconsistencies with them. I've done close to 10 sets with this mold and the effected consistently have warping in the same spots and i am not using rubber bands or tape. I let the mold stick to itself without assistance. It's good to get your feet wet and experiment though. I have my own printed masters on the way from Arcana Cast and will be creating my own cap molds (less sanding with those). Also sharp edged dice are a lot easier to sand because of the flat faces, definitely get sharp edge dice if you plan to make a lot because it's extremely time consuming to perfectly sand the mold line alllll around each dice. Like a skirt of hell! I'm sorry, but for the price we're paying I cannot give any more stars because some pieces are uneven.

This is an amazing mold! The dice all came out perfectly and it was easy to demold!!! It also came SO fast!!! Thank you!!!

I have purchased multiples of the individual molds and have been extremely happy with them. This was the first time I purchased an entire set mold. I am not sure if it was sliced appropriately in half. It seems like it would have worked a lot better if the holes were on the other side especially when compared to the individual molds.I am still working to get viable dice out of it. Its heavily prone to leaking even after being almost 1/2 of the way filled, harden with tape put around it and being weighed down once filled.The reason I am giving it three stars is I can complete my objective of getting dice although it takes multiple re-pours, using a tooth pick, had widen the pouring holes. I would probably look elsewhere if I was to do it again especially given the price.If you do get this one, prepare for a learning curve.