Magnetic Mount 2FT LED Retrofit Kit,18W 2x2 FT (1 Driver&2 LED Strips),150LM/W,5000K Nature White,0-10V Dimmable,T8 T10 T12 Fluorescent Replacement Troffer Retrofit Kit,Quick Easy Install

These are a nice upgrade. I am asking a lot from these lights as well. These are currently installed on my Sand Blaster Cabinet. Like I said I ask a lot from them in a harsh environment. These lights provide way more light than the previous lights that came with the unit. The best par is they are LED. Better light color and quality. Will last way longer. Not sure what you may need but they are great lights, easy to install and have stood up to a very harsh environment for me.

Easy installation with magnetic mounts and 3M tape on controller. Very pleased

We had been missing our over headlights in our family room for years. These worked perfect. Easy to install. And now we have lights

Product appears to perform as advertised. Magnetic mounts on both light strips and the driver make it a snap to mount components where you want them instantly, and move them if you must. A convenient connector permits easy removal and reconnection of the driver. Light strips get warm, but not hot, to the touch. Driver warms very little. No worries about overheating. Build quality appears very good. Kudos to the designers who made all of this possible at an inexpensive price point.Dimming performance with 0-10V control is smooth and quiet, but limited in range. After dimming to somewhere around 20% of full brightness, lights suddenly turn off completely. As expected, the product is not compatible with standard triac based dimmers. Connecting one produced some audible noise even when set to maximum brightness. Attempts to dim further produced pronounced flickering at higher settings, and flashing at lower settings.Update: Responsiv Blink'n'Dim Adapter for 0-10V dimmable fixtures works well with this product. Unlike most 0-10V dimmers, it does not require you to run low voltage control wires between the fixture and dimmer switch. ASIN is B07H3FDQCT.

I have installed a number of these LED lighting strip systems throughout my house and they are great! This time I installed them in a dark hallway in my basement. I clipped the 2/2” light strips onto the metal lattice of a drop ceiling system with the attached, powerful, magnets. The strips throw a phenomenal amount of light. The wiring is relatively simple and could probably be done with 2 lead extension cord or zip wire. (Always follow your local wiring codes!) I highly recommend these retrofit kits!

The strip lights and controller are all magnetic. Used them in a media blast cabinet; lighting is awesome.

I used this product to retrofit seven old 2 'x 2' U-tube fluorescent lights in my basement and they worked perfectly. I started by stripping out all the old fluorescent components till I had an empty steel housing to work with (be sure to disconnect the power before doing this). The magnets made it easy to get the placement of the new LED lights exactly where I wanted them. I paced the controller on one end where it could not be seen thanks to it being painted white and connected the wiring with the included wire nuts.. Once I was satisfied on the placement and the light distribution I just repeated the process 6 more times. In all it took about half a day. I would recommend using the covered LED strips if your light cover is the older plastic frosted type as mine were. It spreads the light from the LEDs evenly and looks like the old fluorescent tubes from below but with the reliability of LEDs . Some reviews have said that they are not bright enough but I feel they are brighter then the old fluorescent tubes I replaced.

Purchased a large coffin top rolling toolbox and added this with a BindmMaster 3 Prong Grounded Single Port Power Adapter with Red Light Indicator On/Off Switch and a Leviton 101AN 15 Amp, 125 Volt 2-Pole 2-Wire, Non-Polarized Angle Plug, at the top of the lid when it is open. It lights up the top of the toolbox perfectly.

Saw a few video’s suggesting these types of lights inside the HF or Princess Auto Cabinet. The factory light was impossibly dim. These lights are sealed and covered and super bright.The magnetic bases work perfectly for holding the light and ballast in place.Would recommend.Note: I need to replace my glass protector, it’s far brighter than the photo looks. All the lights in the shop were on, before I couldn’t see inside with the shop lights on.

Did exactly what it needed to do and was super easy to install.

excellent