YANF 2-Pack 24 Inches DRL LED Light Strip, White-Amber Sequence, Flexible and Durable, Waterproof and Buckled Plug Design, Easy to Install, Fit for Any 12V Vehicle

I super glued these on a 2004 Civic EX sedan headlights. Headlamp assemblies are new. They have 8000K LED headlights installed. With halogen amber turn signal parking bulbs.It comes with 6 little plastic clamp and really tiny screws. Good luck with that! Not sure that would even hold. I think the tiny screws are supposed to screw in the headlight plastic. No instructions on mounting. I was planning on gluing them anyway. The super hold really well! The first time I glued them I used 3M badge and emblem adhesive. It did not stick to the silicone tubes at all. And I was able to peel it off of the headlight. Be very careful if you use super glue. Have a second person help and have some masking tape ready.It is a lot of work to install them! I took my time and put many hours in. I had to go through the wheel well to get at the turn signal wires. I got power from under the dash with a fuse tap. I ran the wire from under the dash through the top of the driver's side fender. I noticed it went through from the inside of the door to the engine bay. It was easier than going through the firewall.I carefully connected everything and put all the wires in heat-resistant nylon wire looms. You will need a lot of wire and electrical tape.They look amazing! Switches from DRL to turn signals flow. I love the ice blue color! Look at the pics!I am sure I will update and edit this as need. I'd be glad to answer any questions.

The LED strips were 24 in long and flat - which made it easy to lay across a headlight surface. This did make the 90 degree turns somewhat difficult to negotiate but I made it. Wiring is very easy. Just run a 18 or 16 gauge wire from the negative terminal to the headlight, then go to the fuse box and locate an ACC terminal (usually a fuse will be plugged in). I ran a wire from a fuse in the fuse box under the hood, stuck in the terminal then put the fuse back in - ACC power. I then soldered (you can use wire nuts) the black (to negative) and red wires (to the ACC) from the LED strip together. That's it. I had power. Then I pulled the 3M backing adhesive - put some Gorilla glue as added insurance and put in place around the lights. They look factory.

I bought these lights for the "eyebrows" of the Polaris Slingshot as they came recommended on one of the forums and were about 1/4th the price of the other Slingshot LED suppliers. They are hard to see in the picture, but they are right above the front outside headlights running along that upper white lip on the fender.Since the hood opens forward on the Slingshot, I thought I had enough wire with the module - but I didn't - my own fault. Since I originally bought 2 sets but only installed 1, I had an extra one and I made sure to extend the wires to give me plenty of slack.The only draw back I could find was the adhesive was not the best. The front lip of the Slingshot fender is somewhat shaped like a question mark (?) around the corner so I had to flex the wire around the bends. The LEDs bent fine, but the adhesive didn't want to stick well on the curves even though it was a cleaned painted surface (I used rubbing alcohol to clean it). I did have to add some super glue to the ends of the lights and even replaced some of the double sided tape it came with.Only other longer term issue might be the little PCB box assy. It doesn't seem to be water proofed. I didn't have any shrink wrap in the right size so I just wrapped lots of electrical tape around it. I glued it in behind the headlights so it shouldn't get any direct water, but it's possible to get some spray from the tires. I'll update in the future if I see any issues with that.That being said, I would still buy these again.

The media could not be loaded.  Like the modern look. Works well on my Toyota 2006 Camry. I bought halo angel hid blue units before and this sequence flashes yellow and stays white daytime running. I have the daylight confiqured to to the ignition key on. Sharp! I didn't cut mine just tucked about 1.5 inches under edge. I bought another pair from a Chinese retailer and upon assembling one side did light all the way. Facebook Cozzz don't recommend. They wouldn't give full refund. I'm glad I check other sellers and this distributor worked right out the box with no problems. Also warranty to(I can't remember how long)

Update: changed from 3 to 1 star. Item started falling off and wasn’t sticking anymore, so I purchased outdoor double sided tape. As I was getting ready to replace the lights, half the LED’s stopped working and wouldn’t go back on no matter what I tried. Unhooked everything and returning these.Product was exactly as described, and had most of the necessary wiring and adhesive for what I needed. We did have to purchase additional wire as well as connectors because the length was not quite enough to get to the battery and fuse box. Although we only used a portion of the strip because I didn’t measure ahead of time, and we are not at this point using the yellow turn signal, it seems to work fairly well although not as bright as I would like during the day. We will see how well it lasts in the rain and harsh Chicago winters, and I may update this and or upgrade the lights at that point.

Product works as advertised, but isn’t exactly what’s advertised. First off they look nothing like the pictures. The pictures lead you believe they are nearly flat when I reality they are at least half an inche tall. There are no cut marks so I just guessed and got lucky with them still working. Lastly, and most annoying, is the mounting kit. They don’t come with double sided tape but little plastic brackets you have screw in. You have 48 inches of tube to secure. You get six clips. The material these are made from don’t accept double sided tape either. So it’s either the plastic brackets or zip tie them on. It’s a good kit just a little different than the pics and a much different mounting kit.

Awesome Product and awesome seller. Had an issue with one side of the LED lights and before the Warranty days were getting over, I contacted the seller and they were willing to replace those lights for free. It looks good and is bright enough to Catch attention. Easy to install to those who know how to install and over all a good product.