OVERTURE Matte PLA 3D Printer Filament Black 1.75 × 1 | Frosted Matt Finish Hides Layer Lines, 1kg Spool (2.2lbs) Cardboard Spool, Fit Most FDM Printer (Matte Black)

Just WOW!. I'll update with photos of my prints later on. I've been searching for matte filaments and there seems to be limited options. Not only have i think i found it, i dear say i found my goldilocks filament. Ordering 3 more rolls next week as I've been printing 24hrs a day since i got it a few days ago. Excited to try other colors. Roll was nicely wound and print quality is astounding, printing is very easily and was dialed very quickly. and i have zero complaints so far. Layer lines are pretty much invisible even at .2 layer heights. .13 is jaw dropping. Been printing an order for a local hobby shop and they at first didn't believe it was 3d printed as it looked multitudes better than previous filament I've used on their order. I've been printing on my mostly stock ender 3 v2. Only modifications are z-brace rods, bltouch, dual z and printed z motor mounts. Printing here the update NY winter is usually challenging as where i print in my home can be as low as 10c ( will be finishing my enclosure soon). Saying that my only struggle has been minor corner warping and bed adhesion. but i doubt that would be an issue in warmer rooms. The issue has been resolved though as i really squish my first layer (leaves very fine elephant foot that cleans quite easily with a sharp hobby knife or 220grit sand paper) since i print 7-20 parts at a time. Can't afford failures. I am printing on the stock textured side of the ender 3 glass bed. For those with an ender 3 i do Hot end at 195-200c, 60c bed temp at 40mm sec (as i prefer quality over speed ) retract 6.5mm 50mmsec, default cura coasting settings and filament equalizer enabled. 75%-100% fan after initial 2 layers. I'd also like to add that my printed upgrades are done in hatchbox abs for strength and temperature resistance. But now any parts that aren't at risk of high temperature exposure I'm using this matte black pla because it looks that amazing and is suitably strong. If I run into any issues I'll update accordingly. Update 7 Days Later So i ordered this filament for an order for a hobby shop. Printing drag racing slot car stands. I printed 96 of these in 4 different filaments. After the first 28 this filament arrived and after the first test prints i was amazed and now only use this filament. I went through the whole 1kg roll in 6 days. Ordered another and already been printing into the 2nd roll. I've updated my nozzle temp to 210c and I'm using a .8 brass nozzle. A worth while mention is these stands i print they're only 3 bottom 2 top, 1 perimeter and 0% infill. And they're almost perfect, very light and just as strong as previous prints with .4 using 3b 4t and 2 perimeter. The watering can is from thingiverse and printed at 60mmsec, 3 bottom and in vase mode. Also worth noting i check filament diameter periodically as i go through the roll and so far it's been between 1.72-1.77mm. Overall still my new favorite go to pla. I definitely prefer a matte finish and this filament definitely delivers.

The finish of this filament is easily my favorite. Structurally, it's not as robust as their PLA Professional. My biggest warning is this filament can be a bear to extrude right if your extruder setup isn't in perfect shape. The matte finish tends to slip more than regular pla in the extruder gears. If you can overcome that, it's a fantastic filament. Just make sure you properly dry it. Matte pla and petg absolutely suck up moisture.

Ive always had a great experience with overture. But the last two spools I ordered of the matte black PLA were very inconsistent with the color. I used the some of a recent spool and it was the same great quality and swapped to one of the new one just because it was a fresh spool and a big print with multiple parts that are assembled together and it was lacking in color it was very faded to the normal quality so I swapped to the older one to check and it was perfect so swapped to the other new spool to check and it was the same issue. My guess is there was a problem with the mixture when making it because both new spools had similar batch numbers. Kind of a bummer and threw me off from the filament for now....

Overeture has been my go to brand for years now. I have NEVER had any issue with their filament. It prints with no stringing - even sitting out in the open for months at a time in our Deep South Southern Humidity ... i.e. pretty constantly above 75% - so bad that all of our tools have to have a weekly coating of oil or they rust and the paper in our printer stays damp in the summer! The filament never clogs and has never been brittle. The finish is beautiful and smooth. And, for PLA, it's pretty tough. I print and sell lawnmower blade balancer adapters using this and my own personal set has held up for almost ten years in a rough, working, small engine shop! I cannot recommend Overture filament enough!

Absolutely love this filament, excellent adhesion. Beats the filament that is made by the same company as my printer. 100% will buy again.