NoctuaNF-A14 iPPC-2000 IP67 PWM, Heavy Duty Cooling Fan, 4-Pin, 2000 RPM (140mm, Black)

Have had these for nearly 1 1/2 years at the time of this review. While high priced, you get what you paid for, functionally at least. I have 4 of these fans in a large liquid cooled rig blowing over a 560mm radiator hooked up to a high end fan controller through a 4-pin specific fan hub. At least with the right monitoring and control hardware along with a distributed heat dissipation setup, these fans can cover the range of silent operation to very good performance, better than anything else I have tried and I have tried a lot of different fans over time. My preferred method of more precise control is to monitor coolant temp and adjust fan speed accordingly as CPU temp for example can jump around wildly without any real bearing on coolant temp, especially with such a large radiator holding down coolant temps pretty much no matter what and there are other components in the loop anyway.Some key points to this fan are:1. One of the best speed / static pressure to noise ratios of any fan on the market today.2. Motor itself is dead quiet. Only hear whooshing fan noise when revved up high. Most any other PWM fans in this category on the market has an annoying motor whine, but this one uses a quite sine wave speed controller (converting the incoming PWM signal to a variable sine wave) and smooth 6 pole motor.3. Out of several fans purchased, all still have perfect bearings, even after 1 1/2 years. All competing fans I have tried in any volume have had at least one bad, noisy bearing in the batch, at least by this point. Especially when doing arrays of fans on radiators, this has frustrated me as it is a bit of a PITA zeroing in on that bad fan, but with these no such thing has ever happened.4. Fan can handle water and dust very well from what I hear. I use HEPA filters to reduce dust in my operating environment and my liquid cooling setup has been leak free, so have not put these points to the real test yet.5. Wide speed range. I have run the gamut from 250 RPM, which is half of the rated minimum speed to 2,000 RPM and these fans have operated flawlessly throughout this range.For optimal operation I have come up with the following (for my liquid cooled setup):1. For a high powered system, distribute heat load across multiple fans so all can spin relatively slowly and quietly.2. The fans are optimized for certain operational parameters around it. Don't place directly up against restrictive intake grates. Recess intake of fan away from restrictive grates if possible. For radiators, only use fans on one side, do not do a push / pull combo. All of these things seem to disrupt careful airflow modeling around the fan blades and cause turbulence, which leads to significant extra noise as the fans are revved up. I at first tried push/pull with these fans, but found I get better cooling performance per unit of noise with the fans on just one side as I can rev up the fans a lot higher before I hear them now and even in the higher than I need range it is still a lot quieter.3. For fan speed in a quiet room I would not try to go above 1,100 RPM on these fans as you start hearing them after this (unless your hearing is better than mine). These fans are good enough to move quite a bit of air at this point so say two of these on a 280mm radiator for your 140W TDP CPU will probably do you well for example. Even at 1,500 RPM on these fans is fairly OK sound level wise. If say on a hot day you have a noisy window or wall mounted A/C, it may make sense to crank these up to much noisier ~1,800 RPM while under heavy load as they will probably still be quieter than a noisy A/C at this point and you may need this extra cooling capability anyway when it is particularly hot in the room. (2,000 RPM will probably be heard over most window / wall mounted A/C units.) With how I have things dialed in with the fan controller, if I ever hear the fans, it is either a fresh reboot or something is going wrong causing the temperature sensors to read abnormally high and thus the fan controller to compensate with higher than expected fan speeds before temps getting high enough to trigger an alarm and ultimately an automated emergency shutdown of the system. Anyways at the full 2,000 RPM there is a strong wind coming off of these fans even through fan grates and a thick radiator (at least for me) which provides a sense of extreme overkill.Maybe one thing to consider are the 1,500 RPM version of these fans as if you are using a crappy BIOS based fan controller that does not give you enough control of the speed range, you may find that going over 1,500 RPM is too annoying. However with a quality fan controller, I don't see why it would matter beyond you will probably find yourself not actually using that extra capability or maybe the lower top speed fan comes with prettier vibration dampers around the mounting holes than the brown only option with these.

I’ve competed many builds with these fans now. They are industrial looking which fits with my builds. They work amazing with radiators where you might you might not want go with vardar style fans. If you want RGB then you’re stuck with something like Phanteks halo units which are fine and not overstated.

Bought this fan for use an exhaust for my gaming PC. My system is comprised of a i9 12900K. And a Radeon 6750 XT graphics card. The fan itself seems very well constructed as are most Noctua products. The cooling performance seems great and has dropped my temps by about 5 degrees. My only con would be the fan can be quite loud and is probably the loudest part of my entire system. However, if you set/adjust the fan speed through the motherboard it's fine.

They do work and do stat fairly quiet. But I expect a $30+ single 140MM FAN TO LAST way more than a year (on light use mind you).I'm giving them one more shot and just bought another to replace this dud. But definitely can't be a 5 because of that.

I installed a 280mm AIO hydro cooler, and as is so many times the case you have to modify the second fan to fit the Ram if you don't want low profile Ram. The fans offer higher RPM for better cooling but you loose the RGB, Noctua please get some RGB already.

This fan comes in a box. In the box is the fan and four screws. That is it and it is all I needed.The fan is a plain black fan which I like, but on the corners they put removable Noctua brown colored rubber vibration dampers. This little touch still lets people know this is a Noctua fan but you can easily remove them for an all black fan if you so choose.I put this fan in the back of my Coolermaster HAF X and connected it to the fan 3 header on my Gigabyte G.1 Sniper 3 motherboard. I have the fan speed in the bios set to normal.When the system is idle on the desktop and I stick my ear right up to it I can hear a tiny buzz sound, but only when my ear is right up to it. My PC sits on my desk and I don't hear it when sitting next to it.When the system warms up and the fan speeds up I can then hear it move air but it is not annoying. When it speeds up it doesn't have any tick or weird annoying sounds.Not all fans that other people seem to like sound good to me. For example, I tried some Cooler Master JetFlo 120 fans in a case because they were getting really good reviews. They looked like nice fans and seemed to be built well. It turned out that they sounded really annoying to me. They bothered me so much that I removed them and put other Noctua fans in the system. This fan has a minimal and unobtrusive sound to it like most other Noctua fans from my experience.Typically if you want the good stuff you will need to pay for it. This fan costs a little more than your average fan but I think that it is worth it. It moves a good bit of air, it is generally quiet in my system, and when I do hear sound it doesn't make any stupid noises that would drive me nuts.It has quality written all over it, an awesome warranty, and the company stands behind their products from what I have read. I wouldn't know though; none of my other 8 Noctua fans installed in my other PCs have ever given me a problem.Overall a great fan that I wouldn't hesitate to recommend.

Added this bad Larry to my case as the rear exhaust and with it's static pressure and airflow, decreased the overall temp by 5-7c all by itself. I knew these were good, but I wasn't expecting THAT good. Highly recommend to anyone on the fence. Thing is a beast, and very solid construction as well!

la única cosa que no me gusto de este modelo de noctua son los tornillos que traen, seria bueno que trajeran otro tipo de tornillos, entiendo que no pueden traer los de tipo silicón, ya que esos los trae los modelos chromax. Dejando eso de lado, en general me encanto este ventilador ya que lo ocupo para el flujo de calor dentro del gabinete, unos muy buenos ventiladores por los cuales se acepta pagar los gastos de importación.

Noctua fans are industry leading for a reason, these fans dropped temps in my case by 5-10 degree CelsiusAt max rpm they are noisy however buyer be warnedI picked industrial version over regular noctua fans because of their superior air flow and static pressure.Industrial fans have bonus of higher durability as well

replaced the fans on my corsair h110i cooler and WOW! No vibration and what appears to be almost half the noise level! very impressed. can not recommend this enough.

Best running flawlessly for the past month. Seems very well built.

ordered these fans and received two sealed boxes full of garbage. disgusting.