2pcs Super Bright 24W LED Two-Color White Amber Spotlight + 2pcs ON-ON-OFF Switch, Waterproof auxiliary Motorcycle Headlight Fog Light, Universal For Car Truck ATV Offroad SUV Driving Work Spot Lamp

Wide voltage range! Some users complaining about output might be using 12v. I can tell you at 50v the light output is pretty good and beam is tightly focused not a flood light. Small size, not expensive, looks durable. So far these look great. Theses are for a power wheels toy so I don’t want the lights to use up a lot of power. I didn’t want to use a voltage rectifier to reduce voltage because they waste energy In the form of heat. The switch is a nice bonus as are the multiple light modes including strobe. So far my only complaint is the wires are a bit on the thin size, prob 20-22 gauge so strain relief FYI.

Love the lights, they were on the smaller side. I thought they were a little larger in size. Overall, does what it says.

Crazy projection right out of the box... we're still tripping on the beam. The beam is also rectangular with a decent edge. Wouldn't say its crisp, but sweet enough for the money.We live in rural.. ain't no lights out here.. these things projected a clean beam.half way down my street.. and that was one beam.. we just attached to a motorcycle batt to test..If these don't rattle to death on my toys and trucks, for 20 I'll buy a set for everything with wheels... even a mntn bike.. these things shocked us, and we did this on a whim.. glad we did.

These lights are junk!The lights might be waterproof but the switch definitely isn't, the included switch is terrible. Check out the picture!The mount bracket is flimsy and hard to use. It was mangled as I tried to tighten it down enough to not move on my mount and its all but impossible to tighten the lights down enough to keep them from "walking" down.The lights are not very bright. They might, and I mean MIGHT help me be more visible but they do not offer any added lighting for my driving experience. I may reconfigure these as turn signals as that is about as bright as they are.The only big pro to the lights is they are lightweight! If only they were brighter and had a better mounting system or at the very least, came with a half way decent switch.

Pros: Inexpensive, bright, made of metal instead of plastic, works as advertised.Cons: Very limited adjustment, no instructions whatsoever (see below for wiring instructions), supplied wiring too short, no fuse included.These do what they say they'll do but I had to monkey around with them to get them aimed and connected correctly.As far as aiming, the only way to adjust them is to loosen the clamp and rotate them on the bar they're clamped to. In other words, they rotate on that axis only. I have them mounted on Hepco and Becker crash bars and there is no part of them that is straight up and down, which is what it would take to get these aimed straight ahead. You could also get them aimed straight ahead if you have a horizontal bar to mount them to that is perpendicular to the bike's direction of travel, such as turn signal arms.But I wanted mine on the crash bars. As it was, both lights were aimed at the ground about 20 feet in front of the bike. This made the lights appear to be very dim from straight ahead. So I had to improvise. There are two small screws that hold one half of the clamp to each light's housing. I removed the rear screw so I could rotate the light up on the one screw that was left. I put Loctite thread locker on that screw to make sure it wouldn't vibrate out since it is now the only screw holding the light to the clamp. I then added some glue (RV Goop) between the light housing and the clamp for added stability. They are now aimed correctly and hopefully will stay that way. Click "Read More" to continue....Wire length - The wires attached to the lights and the switch are too short. Count on having to splice some longer wires to them (18 gauge wire should be more than enough for the light load of these lights, something like 2.3 amps each).Wiring instructions - follow these instructions at your own risk. Below are instructions for two types of connections, wiring directly to the battery or using a relay. Note that connecting straight to the battery makes it possible to drain your battery if you forget to turn the light switch off after your ride. If you'd rather wire it so the light switch is only activated when the ignition is turned on, go to the "Instructions for wiring with a relay" section below.INSTRUCTIONS FOR WIRING DIRECTLY TO THE BATTERY 1. Disconnect the wire(s) from the battery's negative terminal to prevent shorts while you're working.2. The lights each have two wires coming from them - a red and a black. Connect the black wires from the lights to the bike's frame (assuming it's a negative ground bike). You could also connect them to the negative battery terminal.3. Connect the red wires from each light together and then also connect the green wire from the light kit's switch to the same connection. So you now have two reds and a green all connected together.4. Connect the red wire from the light kit's switch to one side of a 5 amp fuse that you have to supply since it isn't included in the kit. Then connect the other side of the fuse to the battery's positive terminal.5. Reconnect the wires to the battery's negative terminal that you disconnected in step 1, and test your lights.INSTRUCTIONS FOR WIRING WITH A RELAYMost auto parts stores should sell relays. You only need one 12-volt SPST (Single Pole Single Throw) relay. It's hard to find a single one here on Amazon, but here is a listing for a 2-pack of 12v SPST relays: https://smile.amazon.com/2PCS-Relay-Vehicle-Switches-Starters/dp/B07B7GS4K3/ref=sr_1_9?ie=UTF8&qid=1529943423&sr=8-9&keywords=spst+relay+12v1. Disconnect the wires from the battery's negative terminal for safety.2. Connect the signal wire to the relay. The signal wire is any wire on your bike that is energized when the ignition key is turned on. About any wire that has 12v present when the key is turned on, but no voltage when the key is turned off, will work. You will need to see your particular relay's instructions to determine which terminal to connect it to. One of the relay's terminals will connect to the signal wire, and another terminal will connect to ground (frame or battery negative). The relay's instructions should identify these two terminals.3. Connect the black wires from each of the lights to ground. "Ground" could be the negative battery terminal or bare metal on the bike's frame (if your bike has negative ground).4. Connect the red wires from each of the lights together on one of the relay's NO (Normally Open) terminals. Again, see the relay's instruction sheet.to identify which terminals are NO terminals.5. Connect the green wire from the light kit's switch to the NO terminal on the relay.that is paired with the terminal that you connected the red wires to in step 4. The relay's instruction sheet should identify the paired NO terminals.6. Connect the red wire from the light kit's switch to a 5 amp fuse that you have to supply since it isn't included in the kit, then connect the other end of the fuse to the battery's positive terminal.7. Reconnect the battery's negative terminal wires that you disconnected in step 1, turn the ignition to the on position, and test your lights.

Fast shipping. Thank you

I installed these on my 2012 V-Strom to add extra lighting to the front of my bike for safety reasons. My fellow riders have all commented how visible these lights are. There are 3 modes: Low, High and Flashing. I would have preferred the High Beam only mode but for this price you can't beat it. With the supplied switch, you simply turn the power off and on to get to the desired mode. I believe it defaults to the last mode when the power remains off for several minutes. There are two screws that attach the light housing to the bracket. I wrapped some electrical tape around the rubber turn signal extensions for protection and mounted my lights to them. There was just enough play, after loosening those screws and then retightening them, to allow me to point the lights in more of a horizontally outward position. One may have to remove one of the screws to the bracket permanently if more horizontal adjustment is necessary. I do have one minor gripe... the lights came with a white connector sticking out the back of the light as opposed to a black one shown in the picture. A little spray paint or electrical tape can help solve this if it is a problem.

these work, make a focused intense beam, and are pretty reliable as long as you dont leave them in the rain for MONTHS. they are thru drilled and tapped, so water will weep in the holes and flood the PCB.

Both switches did not work and the lights when plugged in flicker not impressed

The media could not be loaded. Buena luz, lastima que con dos lavadas a la moto y una lluvia el lente presenta humedad en su interior. Además los controles no son buenos para controlar cada uno las iluminaciones que trae ( blanco y ámbar). No lo recomiendo.