Fatshark Black Fan Face Plate for Attitude V3 FPV Goggle FSV2617

A great improvement on the rubber eyecups, needed a slight mod to fit the v2 goggles, I used double sided tape under the fan housing and a couple of spots of hot melt glue at the bottom of the frame, works nicely.

Perfect.does what is says to an old problem that many experience. Great value easy fix.

very good

I bought this to use on my Skyzone V1 goggles and the fit is much more comfortable, but the fan is the weak point. I had a problem with fogging and this didn't really help. The fan starts out whisper quiet and works well, but after about 15 seconds it gets REALLY loud and hardly does anything to prevent fogging at all. Can't even focus on flying when it sounds like there is a weed wacker attached to the goggles I am wearing, not to mention I can feel the vibrations of the fan spinning. I am guessing the fan is just not balanced properly which is why it makes so much noise and vibrations.

After looking at the newer Fat shark googles, thought about upgrading after selling my old ones. I realize that I was fine without the DVR and the desire to buy the Radio module as separate... like wtf... haha So I went ahead and bought this to attach to the goggles and the optical lenses for near sighted people like myself. After these two upgrades, I felt like I upgraded to something much better than before. I never have the issues with my goggles fogging up and wearing them is SO much more comfortable without needing contacts or dealing with the eye cups. Granted, they won't just attach easily onto the goggles. I just use black electrical tape and it does the job. I used some hot glue on a low setting to attach the lenses and that worked just fine. If I ever do decide to get my Ham license, I'll just buy a 1.2Ghz system and hook it up to a 3S system. But until then, I don't need to fly long-range, just long term without fogged and uncomfortable goggles.

Great quality, put them on my Dominator 3rd generation Fatsharks, clear double sided tape under the fan and stick great, didn't put the tape all over it like in the YouTube videos, unnecessary. Not as comfortable as MX goggles by any means but better than the eye cups for sure, when the goggles are on it don't get any light leakage, if I pull them away from my face a little I can see the light gap between the goggles and faceplate but not when they're on normally, foam pads also come up in the nose area, so there's no gap for light, definitely worth the purchase

Bought this face plate for my Attitude V2's because I love this same face plate on my V3's. Though requires a little bit of ingenuity to get them attached and get the light leaks sealed, the face plate works well on the V2's.Remember to purchase the larger carry case so you can store the goggles after you attach the face plate. Here's the link - https://www.amazon.com/dp/B019OM7CR8/ref=cm_cr_ryp_prd_ttl_sol_14

I have the Fatshark V2 but thought I would give this a try. My lenses fog up while flying FPV and I can't see a thing. This setup fits pmy Fatshark V2 goggles but with the V2 goggles you'll need a solution to connect to your goggles. I 3d printed some clips from Thingiverse and it works just fine. I can actually feel the air blowing on my eyeballs. It has effectively eliminated the fogging problem. I gave it 4 stars because it was not a perfect fit but its good enough to solve my problem.

The unit worked well initially, the kept my goggles from fogging and were comfortable to wear. However, about 5 months later the fan failed and no longer works at all rendering them useless now. I expect a product to last much longer since I've always taken great care of them by storing them in a case and handling them with care. Really disappointed.

Bought this to convert my FatShark Attitude V1's to the Dominator V3's. Works great, I love the fan!!!They face plate really doesn't fit the attitude very well, only because it's not made for them. but fit good enough to use with out a problem.Now if I could only find some tape that will stick to the goggles.....

Used this with a SkyZone v1 with 3D printed clips. Much better then the eye cups that is came with. Plus you get the fan and cushions that make it way more comfortable to use.

Great upgrade to the attitude v2 that comes without a faceplate. Almost snaps directly in place just need some mounting tape, don't use super glue, when you turn fan on it blows burning super glue air in your eyes lol

We use these on the Skyview goggles, worked perfect, great product!

Added to my old Attitude V2 headset. Pull off the old eye cups and glue these on. I recommend getting some black hot glue to secure the faceplate. Makes a huge difference in hot/humid flying conditions.

I bought this for my Attitude v2. I originally used double sided tape to attach it to my goggles but I found some clips that I printed on a 3d printer that holds it perfectly. This is so much more comfortable than the eye cups.

Much better then the rubber cups that I seem to to have problems fitting and adjusting to my face.These should come with the goggles, like going from tighty whiteys to boxer shorts.jmoOh, the fan makes for a good idea to.

works great, fast shipping

For $30 I should not have to hot glue it on for it to stay on the goggles. Also the fan switch worked once then broke, now I have to turn the fan on/off by plugging/unplugging the balance lead. Save yourself the money and just 3D print the one off of Thingiverse. I regret buying this.