SUNLUSilk PLA Filament 1.75mm, Neatly Wound Shiny PLA 3D Printer Filament, Dimensional Accuracy +/- 0.02mm, Fit Most 3D Printers, Good Vacuum Packaging, 1kg Spool(2.2lbs), 330 Meters, Silky Gold

'A Good and Superb PLA!'Frankly Id heard many fine things and some favorable comment on SUNLU Filaments!So having bought a roll an done a project I can Honestly Report that most of the favorable things reported are in truth correct as it is a 'Very Fine' Plastic and SUNLU definitely has its act together!!!.PROS:Makes a Neat an Classy looking Part!Easy to Run, Easy to Set Up!Its the Real Deal You Get A Full Roll of !st Class Filament!Almost the Only Silk PLA Plus+ on the Market!!!!!A Real Bargain as the Price is Fantastic for what you get!.Fast Amazon Shipping cannot be Beat!!!!!CONS:None actually cept If Id known this was a PLA+ Id have ordered it sooner!!!!!In General:Now In My Useage The SUNLU worked and printed quite well.Setup was simple, I use Sticky Blue painters tape.Set Nozzle at 259 and Bed 109 and let warmup for 10-15 mins.I set 1st Layer at Nozzle 257 Bed 100, Speed at 35 or 40!Then after 1st layer is down and hard I set the rest of the run at about say:Nozzle 250- or 255 Bed 60 0r 75 and let Speed run at 45...True "I Know" at those settings Ill get some stringing but 'I dont have any problems with layers not bonding and It don't take 'All Day' to get the part finished either.Yes I know there are all kinds of 'Micro-settings, But I know that most machines have there own 'Pet Settings for wanting to run right.Now most folks want to run 'Cold and Fast' But I tried that and got a LOT of junk parts!.For me I found that "Slow but Hot" seems to get 'Better Parts'.....Me I adjust my speed with a New Plastic until Stringing starts to appear then I back off fast!.I also run my tests a 'Bit Differently' as many will run a ducky or a benchly and its a good way.For Myself I have a small but 'difficult part', See it dont take much Plastic but if the plastic is good enoughto make a 'Difficult Part' then the easy stuff will run Home Free as the SUNLU did!!!!!!!!!!Now One Major Complaint w Sunlu is it doesnt extrude well or the teeth dont grip the Plastic right!.Yes at one time 'I Had' that issue but here is how I worked around it!.A HOT TIP:Now sooner or later when the teeth wear down you will have to replace that drive extruder gear!.On most new machines its the round Brass One w the two small allen nuts sticking out the top side!Most guys re install the gear wrong, I know I did??????Yes I did as most of us will do what the YouTube guys did as they 'Set It' Plumb in the middle!.Hey if you are satisfied and it works for you go for it!!!!!!!!!!But there's a Better Way, In stead of in the Middle I just slid the Gear down a notch and let the plasticrun off the teeth on the Top Side of the Gear as it grips better and runs smoother too.Oh yes it will surely wear like they all do in time, But if you did it right there is no great need to replace the gear not by any means sic!!!...Just loosen the allens then "CAREFULLY" slide the gear back upwards until the Teeth on the bottom which are still good are NOW gripping the plastic as I think its pretty neat to reuse and get good service from the same part twice!!!!!.TO: Close;SUNLU Silk PLA is super good stuff that is easy to set up, It runs fine and makes a good part!.And to Finish Its the only PLA+ that runs a silk fibre so it has Very Considerable strength and I definitelyIntend to try some Printer Gears with this and the smooth finish makes a classy looking part too!.Kudos to the Seller!Kudos to Amazon!Nuff Said...IndianaED

Works like a charm, ease to use, I had no issue with it. The filament is a bit rough, similar to matte filament. I have a hardened steel nozzle on my printer, so be careful if yours donesnt

I used a Ender 3 S1 bed at 55 and nozzle temp at 210 and this printed like a dream the one thing i learned was to not use glue on your bed just clean it and pri t. This bank took around 52 hours to print and no problems the glow is bright and very pretty the normal color is great. This is so far my favorite filament I will be trying other colors when this runs out.

This stuff was very pleasant to work with. Attached pics are 0.6mm nozzle and 0.2mm resolution prints.Roughly 3" x 5" base plate and about 6" from back to nose. Each on baaaarely got 2.5 colors. I'll admit, I didn't read the description in the body of the seller's page here carefully where they say "each color is about 15m long." The sample images they show are CLEARLY misleading, unless they're using almost to over a full 1kg roll. The photos of the roll, ironically, are fairly accurate. You'll get a full rainbow about every 1/3 roll.So, I'm really disappointed by those misleading print images.That aside, very lovely, very pretty filament for my CR-10. Has a tag on the line too intended to help prevent tangling, so far so good I guess, but the roll hasn't left the Sunlu filament dryer yet.Do us all a favor, Sunlu, ditch the false advertising print photos and show some that either were actually printed using THIS product and/or aren't so huge enough to actually get a rainbow going on a single print, yet alone 2+ like the pictures. Honestly would've gone with another roll if I'd known almost everything was likely to be duo-tone with a hint of a 3rd color. Plenty of that for less than this roll costs.

This filament prints easy with great layer adhesion. I used a .6mm hardened steal nozzle with the build plate set to 60° and the nozzle to 220°. Cleanup was almost completely unnecessary since any stringing or glops came right off with my finger.That aside, my research suggested that PLA+ had a heat resistance of around 60°-65°c unfortunately after only one day in my car, as a test, the parts failed. The outside temperature never exceeded 80°f. (See picture above)I will say I love the feel of this material as well as its physical strength, dementional accuracy, and appearance.I did beat the crap out of one test piece with a hardened rubber mallet, driving two pieces together. Both pieces held up beautifully.

Me encanta que sunlu venda el puro filamento. Ojalá más colores y marcas hicieran lo mismo. Además sunlu es una buena marca a precio promedio.

Muy maltratada la caja, pero el producto está en buenas condiciones, se imprime fácil y da buen resultado. Parece que tiene un porcentaje bajo de fibra de madera porque el aroma al imprimir es mínimo y en la textura de la pieza impresa tampoco se percibe mucha diferencia, pero igualmente el resultado de la impresión es bueno.

Es un filamento fácil de imprimir, tan solo fue necesario hacer tests de temperatura, luego de eso imprimí el modelo de 130 gramos y se aprecian 3 cambios de color. El problema es que no son colores tan vivos como se muestran en la imagen.

bon

Das schwarze PLA war okay, aber das graue PLA bricht ständig. Sogar auf der Spule. Der Filamentsensor rettet mich zwar in der Regel, aber trotzdem muss ich auch oft genug Filamentreste mitten im Druck manuell entfernen und der Druck wird unsauber...