Cabinet Push to Open Latch, Jiayi Heavy Duty Push Open Latches, Magnetic Touch Release Latch Magnetic Push Release Catch for Wardrobe Hidden Large Door Closure (White, 2 Pack)

Well designed product

strongest magnet I could find

Well built product, but way too strong for my application. Springs take a lot of force to properly close.UPDATE: Just three months after installation, one unit does not latch easily. Many attempts needed before it remains latched. Disappointing!UPDATE 2: After reading my comment, Jiayi offered to replace the defective part, which I received in just a few days. Impressed with the level of customer service, and upping my rating to four stars

These were a direct replacement for existing latches that were failing to close all the way. They were an exact fit and they work perfectly.

These didn't work well for my application because the throw and spring tension didnt match well with my sof close mechanisms. I'm wanting these as a push to open mechanism (PTOM) for the pocket doors in my house, which are equipped with soft open and close mechanisms (SOCM).Ideally the pocket door could be slid open at the lowest speed possible, hit the PTOM, and the SOCM would carry the door all the way into the pocket, latching the PTOM into the closed position. If you know anything about springs and soft close mechanisms, you should see the paradox here.The springs in the PTOM need to be soft enough that the SOCM can fully retract and latch the PTOM, but then they need to be stiff enough to overcome the SOCM when you push in and release the PTOM. As far as I know this is physically impossible. However, there is at least one YouTube video (he used these units) that says this capability exists in Canada or Europe or maybe both...no clue how you can do it though because the PTOM needs to have a weaker spring than the SOCM upon opening the door (closing the PTOM), but a stronger spring upon closing the pocket door (releasing the PTOM).The other thing you need to look out for is having the correct throw. If the throw is too long, the SOCM will not "grab" the door before it hits the PTOM. This will cause the door to bounce off the PTOM. Unless you use the magnets maybe. I didn't because the SOCM should hold the door into the PTOM and the magnets would make it unnecessarily more difficult to pull out of the pocket. On the other side, if the throw is too short, the door won't come out of the pocket far enough to grab. The ideal throw would allow the SOCM to just barely grab before hitting the PTOM, and then when releasing PTOM it would be able to just barely escape the clutches of the SOCM.In the end physics still wins and this unit was simply not a good match for my SOCMs.I give these three stars because they are nice units but not working for my application. But apparently (according to a statement on YouTube, i could find 0 examples though) Canada and Europe has exactly what I need but nobody sells it in the states and I'm trying to encourage getting them here.Ultimately someone should sell a PTOM with a matching SOCM that are designed to work as I described above. But since, throw and spring force both need to be matched, a single manufacturer would probably be the only one who could make it work perfectly, if it's possible. Or a unit with tuneable spring tension and throw may be the best option, but then it would probably cost a lot more and i didn't see any like that. However these can easily be opened up and you can change the spring and maybe even the throw somehow. I really wanted to try the "EZ OPEN" PTOM. but at $45 a pop, I wasnt willing to experiment with that kind of money.I ended up going with a 3-4" long round unit that was, less expensive, much easier to install and has much better throw for my application than these ones.

The media could not be loaded. This was very easy ti work with. I used soft close hinges and this latch to create a hidden door on the side of my fireplace. I loved the way it turned out. It took a little bit of time to get the depth perfectly aligned but totally worth it. The magnet is definitely strong enough for my door too. I only used one on the top left.

I needed a product to open a draw and cabinet that were installed too close to a door of the dish washer and could not use a standard pull this did the trick

Plastic made very poorly. Says heavy duty in description. Not my idea of heavy duty. Holds light weight door somewhat securely with 3 of them. Good for small projects I suppose. Not large solid wood construction