Drilax Diamond Drill Bits for Stone, Glass, Dremel 1-2-3mm 30-Pc 1/8 Shank

Good set of diamond bits for the price. They worked exactly as they should and did the job without any issues. Nice variety of sizes too. Fit perfect inside my Dremel tool. Lasted for the entire project!

These drill bits work great! I’ve used them to sink holes into glass, shells and light weight metals. They fit nicely into my dremel. Looking forward to getting a lot of use out of them.

Good for the price. I would say these for a small job, but if you need drill any holes in ceramic or similar material, I would recommend a better quality diamond bit. Since they are fairly inexpensive, the diamonds wear off quickly. They did what I needed to do.

These are great. I don't think they are supposed to last forever, and that's why they give you multiples. This is my first experience using these diamond tip bits, so I am not sure how the compare to a more expensive brand. I've only used these so far to etch a gemstone that I needed to fit in a setting and it worked well. The multiple sizes are nice. These attach to a Dremel just like any other attachment would. I like having these bit around because you never know what you will need them for. It's also nice to have tools around as an introduction to other hobbies or jobs that may use them in the future. I don't see how you could go wrong with these, especially with how affordable they are. I recommend these to anyone with a Dremel because even if you don't need them immeidately you likely will find a use for them in the future.

This 30-piece diamond drill bit set is a great value for detailed work on stone, glass, gemstones, and jewelry projects. The three included sizes make it easy to create different hole diameters, and the 1/8-inch shanks fit well in a Dremel or other rotary tool. The bits cut cleanly when used at a controlled speed with water for cooling. They are especially useful for sea glass, beads, and small lapidary projects. The variety and quantity are helpful because these small bits can wear over time, especially on harder materials. Overall, this is a practical and affordable set for hobbyists, jewelry makers, and anyone doing precision drilling.

New Review: After more attempts and talking to a professional glass worker I have discovered the trick to drilling through glass with these. Set the drill to the maximum speed possible. A Dremmel tool might not be at the fastest speed setting because it is faster than a drill. Firmly anchor the glass and the drill. The glass should be on a flat wood surface. Lubricate the glass surface with water. Slowly bring the drill to the surface of the glass. Do not apply any pressure. You should be supporting most of the weight of the drill. Initially the water lubricant will turn black. For most diamond drill bits this would mean that they are broken. For this set, it does not mean they are broken. I think the diamonds are coated with a thin layer of titanium or steel that is rubbing off. Replace lubricant every few minutes. After a few replacements it will turn white with drilling instead of black. The drill will drill faster. After you are halfway through, turn the glass over and drill from the other side. It takes about 10-30 minutes to drill through 2mm of glass. This is pretty slow, but it is in my price range so that is what matters in the end. Old Review: I bought these to use to cut FTO coated float glass. The instructions for using diamond drill bits are to use a low rotation speed, and apply only 8-16 pounds of pressure. Using a drill press I was not able to drill through glass using only 16 pounds of pressure, the bit never made it past the surface. When I applied more pressure the diamonds broke off from the surface and acted as a grit to abrade the surface. This did allow the drill to bite into the glass, but it took a very long time (about 15 minutes when higher quality products only take 3) at high pressure and RPM to drill through the glass. Unfortunately this amount of pressure also caused chipping around the edges of the hole and blowout at the other end of the hole, creating an ugly break cone. Each bit could only drill one hole this way before being discarded. Some bits snapped before they drilled through the glass. This product is useless to me. It is possible that these bits could cut into softer stone or sea glass, but for float glass it does not work.

They work great! Fits the Dremel and does the job!

I used these with my rotary tool on sea glass and a few small stones, and the different 1mm, 2mm, and 3mm sizes were really convenient. They’re especially useful when you need precise holes for jewelry projects. I kept the work area wet and used light pressure, which gave me much better control. The storage case is a nice bonus for keeping the tiny bits organized.

Stabile Bohrer die gut bohren.

Perfectas para bisutería; cumplen su función

Take your time, start at an angle and then vertically and keep it wet, we drilled in dish of shallow water. Took about 10 mins to go through 4mm of glass, could have been quicker but didn’t want to apply too much pressure .

All as ordered

Nice product. Excellent price.