Frigidaire 134743500 Washer Motor Control Board for Washing Machines

Easy replacement. Once I got the diagnostic mode working.Initially, I believed RepairClinic who told me it was most likely the valve assembly. It wasn’t (which I discovered during additional poking before that part arrived).To diagnose my machine (a Frigidaire/Electrolux GLTF2940FS1), one turns the knob all the way to the right (Touch up), hit pause to clear the lights, then hold pause and option past the first LED light and then when they all turn on. You then turn the knob counter clockwise 9 clicks to see the last diagnostic code. One can find the diagnostic codes online along with testing protocols ( search for ‘Frigidaire frontline diagnostics’ but know that the diagnostic mode setup is wrong - go to ‘Touch up’).Anyway, once I found the code, I tested the motor per the suggested test which led to the diagnosis of the bad motor control board.I pulled the motor by unbolting 3 5/16 hex screws, and removing the wiring harness from the motor. I then removed the motor control board and removed the three wire harness attachments.The kit comes with a piece of double-sticky tape and no instructions. There are videos on YouTube that show you to use the double-sticky tape on the underside of the mounting bracket which I did. I placed the wires back and then mounted the board. After that, I put the motor back and reconnected those wires as well.The whole job was about 1/2 hour once I got the part. It was harder to move the washer to work on it than to actually replace the board.The washer works like a champ again!

Tech sheet inside the washer indicated motor or motor control board for E59 error. My motor ohm readings looked good (see YouTube video titled "Frigidaire Front Load Washer Won't Spin - How to Test the Motor"), so I removed the motor control board (see Youtube video titled "Washer Motor Control Board (part #134743500) - How To Replace") and when I opened the plastic case, I found a large transistor on the circuit board that had burned up. I ordered this part since it appears to be the exact same part by the original manufacturer. Install was straight forward and the washer now works fine again. Despite warnings in both of the videos, I did manage to cut my hand on the edge of the access panel opening, so beware.

This fixed out Frigidaire Gallery series Model # GLTF2940FS1! The problem we incurred was that somewhere in the middle of a load of wash it stopped working and we were left with soaking wet clothes. The timer continued to the end of the cycle and we never noticed until we went to dry the clothes. At that point we tried the drain/spin cycle which did not work. We then tried all the cycles - none worked. There was power, the lights would come on and with each cycle the appropriate time appeared but it wouldn't fill with water or spin or anything else. The timer would count down, but with no other actions. Searches on line helped us to determine that we had an error code 57 which drew us to this control board which goes in the back behind the motor or the main control board which goes in the front behind the display. We felt we had a 50/50 shot choosing. We concluded that because everything lit up and each cycle would show the appropriate time and all the spin cycles would light up when we changed them as would the water temp lights that the main control board was likely not our problem (so we hoped!). We went with this part, installed it, plugged it back in and gave it a try and it worked! Hooray! It is finishing up a load now as I write this.

Never had a chance to try it. The item came with a little crack on the top. Rather than take a chance, we returned it.

This is an exact OEM part for Frigidaire FAFW3801LW3 washer. I got the dreaded E5E error which meant something in the wiring was broken. Youtube has very helpful videos to check if the motor is working ok (Google how to test Frigidaire washer motor ohm). My motor was fine, which meant either the main control (front of the washer - dial assembly) or the motor control board behind the washer was likely broken. I took and chance and bought this. It fixed the problem.

First item was defective, but a replacement arrived the next day; only reason I put 4/5 stars. Item is working as expected and my washer is back up running.

Part was a match as described, great value, easy swap, works great!

Part arrived fast and at a fair price that it made it worth fixing my washer gltf2940wh rather than buying a new one. Part has been working for months now with no problem. I did not need to replace the motor either as many suggest. I just looked up the error code and replaced this part. HIGHLY RECOMMEND

Produit identique à celui d'origine.

bonne pièce reçu rapidement

Never thought I could do it! As per prior reviews, washer wasn't rotating. Pulled the error code and ordered this online. Was able to swap out the old one in about a half hour! Runs like new.

Le produit fonctionne très bien, bon prix

The board arrived and although it looked different than the one I was replacing, it worked perfectly. Great price!