INLANDPLA 3D Printer Filament - 3D Printing PLA Filament 1.75mm, Dimensional Accuracy +/- 0.03mm - 1kg Cardboard Spool (2.2 lbs), Black PLA

Being somewhat obsessed with glow-in-the-dark things, I've really limited myself to luminous filaments. I've struggled through rolls of Hatchbox for years assuming I was just not getting my print settings right (temperatures and flow too low or high, bed not leveled adequately, wrong speed, nozzle erosion, etc.). I had success with non-GITD filaments, but what's the fun in that?I found the Inland Luminous for a good deal and decided to try it on a whim. I half-heartedly removed my mostly full roll of Hatchbox - which had only given me a few good, small prints, and otherwise just clogged my Ender 3 Pro - and loaded the Inland. I heated and leveled the bed and then started to print some drawers for the E3P I had previously sliced.The first thing I noticed was, even without perfect leveling, adhesion on the magnetic printing mat was great. I had some low spots that I tweaked as the print was running, and the first layer was able to gloss over any missed paths in the brim and complete a nice first layer. Around this time the Hatchbox would typically clog (or a few layers in, after the print looked like it was going to work), so I didn't have much hope, but I stepped away and let the print continue on. A few layers later, the print was looking fantastic, no stringing, no clogging, the infill looked flawless (Hatchbox would frequently leave non-continuous lines in the thin infill sections), the vertical walls had no obvious issues.I left the print go and it turned out perfect. I've seen this before, however, and know that just when I think I have everything tuned in, the printer will remind me who's really in charge. Nope, not this time. Second drawer - perfect. Drawer frame - perfect. Tiny battery holder I had designed - perfect. I downloaded a bunch of things I had been putting off printing because I knew they'd be a pain - all perfect. 2 minute prints, 20 hour prints, everything I've tried has just worked.Not only that, but the glow! The glow is much, much brighter than Hatchbox. The ghostly, milky, off-white color when in light subtly hints that if you're lucky, the object might glow (in the dark). When taken out of the light, even with minimal light exposure and 20% infill, the glow is deep and bright. I've read reviews about other filaments that are brighter but at the time the Inland was what I could find and it does not disappoint. If there truly are brighter GITD filaments, they would have to print as well as this roll has.I haven't had this roll long enough to know how abrasive it is to a brass nozzle. While not completely smooth, the Inland is significantly smoother than Hatchbox which feels like it could double as sandpaper thread. Only time will tell, but after around 30 hours of prints, any nozzle erosion has not been noticeable.My initial impression of the Inland Luminous PLA is that its the unicorn GITD filament I've been looking for. The only downside is that I'm going to be going through a lot of it since I am spending much less time on printer maintenance and much more time actually printing things.

I've been using this filament for a while, but it's only recently that I noticed that the whites aren't as bright as I thought. Turns out all metal hotends are just efficient enough at transferring heat, and make the dye in the black specks (PETG?) run slightly before it can get out of the heat block. Running less hot should help.It's good filament regardless of the little quirks. Zero issue with bed adhesion, layer adhesion, or clogging. It's basic PLA with fun bits inside. It's hard to mess up.

Just bought a 3D printer after wanting one for years. Chose this PLA based off of reviews and price. My machine is an Anycubic Kobra 2 Neo (if it matters) and this PLA worked great in it. It did break once causing a long print to fail but I suspect it was my fault, I think I caused the filament to kink. Other than that no issues at all. No clogging and no stringing. It worked off of default settings, I didn't have to fiddle with it or tune. Will probably buy this again after I try some other brands just to see what's out there. I have used this entire roll.

I use this PLA for fun projects that could use a little something extra. The glow emitted from these once charged is rather nice although not super long lasting as you may be accustomed to if you are used to using glow paint.Consider using a UV light to charge the finished print for a nice even and bright glow. I usually keep additional walls when printing with this material as to have more glow than thin walls which may be a bit transparent.

love the color have bought before and will buy again

This filament is EXTREMELY frustrating to use due to the very poor winding onto the spool. I didn’t even know how many issues this can cause until after I used this material. Your prints can get ruined at any moment because the filament gets bound on the spool and chokes the printer. I have never had this issue with other brands of filament.

I wish I could buy this in bulk. It is one of my favorite filaments all around. It gives everything an elevated and polished look and prints so well. I typically don't sand PLA unless I'm painting over it because it sands terribly, but somehow this stuff is like a dream. Even if I need to do significant cleanup and filing, you can barely notice with this stuff.

This filament's pretty good and definitely durable. Bought this a while ago for some personal projects and it's been holding up pretty well. I will say that for the price it's a little high but not by much. I think with the accuracy of the filament combined with the nice color and extra rigidity that it has compared to some filaments, it's definitely better than a lot of options online. It's really good if you can manage to get into a micro center and get it you know for a bulk deal or some other special.

Recibí mi pedido en el tiempo acordado pero al momento de abrir la caja me di cuenta de que la bolsa con el filamento ya estaba rota aunque el filamento parecía completo.Como tenía una urgencía comencé a usarlo pero al parecer el filamento está usado y ya venía cortado en varias partes.Pésimo producto, puede que la calidad si sea buena pero nadie espera recibir un producto como este ya usado. Que lástima