6.5 Inch (6½") Black Plastic Speaker Adapter Bracket Ring Select Models Compatible with Nissan / Infiniti

Good product well made, perfect fit with old stock adapter on nissan frontier 2002. Most amazon products don’t provide dimensions wherelse competitors provide more info with mm calculation

The front door speakers in my 2002 Nissan Xterra (built in 2001) were factory molded to extend out from the door a couple inches. On some earlier Xterras and Frontiers, this extension - or "spacer ring" - was separate from the speaker and could be reused with after-market 6.5-inch speakers. My setup had the spacer ring and speaker as one piece. Naively, I had given away those stock speakers before realizing I needed the extra space and adapter; some DIYers had cut out the speaker and reused the ring. This Adapter Bracket Ring worked perfectly for my vehicle. It allows the speakers to be mounted out from the door so that 1) the magnets do not interfere with - or sit close to - the door glass when rolled down; and 2) the speakers sit closer to the door panel's speaker grill allowing for better sound projection. Note that the top surface of the adapter/spacer ring is solid. This requires an extra step or two with install but accommodates variances in mounting screw locations of the after-market speaker. Overall, this is much better than the flat adapter rings commonly found at most electronics retailers.

I purchased these Black, Plastic Speaker Adapter Ring Brackets to use Skar Audio - RPX65 6 1/2" 2-Way 4-Ohm Speakers in the front doors of my 2004 Nissan - Sentra 1.8S Car. I used speaker gasket tape & sealed the speaker to the mounting rings for a good seal. The speakers lined right up & so did the three holes on the adapter rings brackets for a perfect fit. These are very good quality unlike other brands sold here on Amazon & are well worth the low cost. I am happy with my purchase & I recommend this product to anyone with a 2004 Nissan - Sentra 1.8S Car.

2014 Nissan Versa fit like a charm. I like how the pre-drilled holes on the outer edge and with-in are included so that mainly any style of 6.5 can be mounted and then placed in the panel. The skarrpx65 have a deep basket that had to be mounted “on” the adapter rather “in”. The 3 holes aligned perfectly with the 3 existing holes to mount into my door and keep moving with my life. Great product!! Great price.

Product fits as described and allows for a good, clean installation. Does not come with any screws, so you'll need to hold on to the mounting screws from your vehicle and from the speaker. Only note on quality: it would be nice if the side that mounts against the door body has some rubberized foam or something to cushion the plastic against the metal to help prevent vibration and make it seat nicely. But it does the job.

Very simple light plastic spacer and adapter for most nissan front door speakers that use 6.5” speakers and mounted with 3 screws to door panel. The adapter looks like you can use 5.25” spkrs too with smaller holes on the inside of the adapter as well as on the ring for 6.5” spkrs. Its not going to give large depth speakers enough room to clear windows so get slim speakers for the door. Otherwise simple to screw on new speakers as small pilot holes are there already. Works well for my 350z.

One of the people asked if they fit Nissan sentra. Answer was 2000-2008 I think. I have a 2005 and these did not line up with the factory bolt holes. Didn't feel like taking my does apart again so just used them with self tapping screws. Not my preference but whatever! So NO THEY DO NOT FIT 2005 Sentra and yes I rotated the three bolt pattern all around and still no lineup.

I ran into a couple things that in my opinion could have been better.The basket on the speakers I installed were not a perfect match for the adapters. I few minutes with a file fixed that part. These were manufactureed with a sharp edge, could have been rounded in the mould, but why make it easy.The speakers coming out used foam between the speakers and the metal of the car door. This product is hard plastic, so I had to improvise. Got some adhesive backed rubber foam at home depot - problem solved.Last - to accommodate the wiring I had to drill a hold through the side. Your application may be different, but in my car the wire harness connects on the cabin side, not inside the door. 3/8" drill bit fixed this.With this done the self tapping screws (included) worked fine to mount the speakers to the adapters. The original hardware attached these to the door and this part of the job was complete. Daughter is happy!

s'ajuste très bien avec Nissan 300zx 2006

Used to install Precision Power P.65C3 6.5" 3-Way in a 2013 Volvo XC60. Some small modifications required to accommodate the basket on the 6.5 drivers. That was expected. Great product!

Fit my car perfectly allowing me to change the speakers.

As described

Fits perfect my Nissan Rogue 2008