Boat Flooring Mat EVA Foam Faux Teak Sea Decking Marine Carpet Boat Decking Mat Non-Slip Self-Adhesive Flooring Material for Boats 94x35 inch

I used this to replace the seating pads on my classic Hobie wave. The key? "Cleanliness is next to godliness" I always say! I removed the old pads, in my case they were able to be removed complete in one piece. Its easy enough to use the old pad as a pattern, I marked spots on the patter to align the gaps on either side of the seat. I cleaned the rinsed the surface and re-glued the caps that are underneath the pads first. I then cleaned the surface using 99% Alcohol pads until nothing else would wipe off. Then I peeled and stuck the pads and trimmed with X-Acto knife. This product stuck well enough that I struggled trimming even small amounts because they were stuck so well. After one day in the hot sun, the ends seemed to curl up some, I had not gotten them wet yet, so I just pressed them back down and placed some weight on the curled edges. The next day they were tight and right and have not peeled anymore. I am going to say this product works well and give it a thumbs up!

First time trying to do my own diy eva foam decking job. This stuff is thick enough to route. Doesn’t feel as firm/dense as SeaDek but that was almost twice as thick as this stuff. I don’t have a cnc (as you can tell from the pics) so templates it with chipboard, cut with razor knife and I free hand routed the inset logo and fish. The edges I used a Dremel barrel sanding tip on a stylus attachment going with the rotation to feather a beveled edge(4hrs!). Not precision by any means, but compared to the cost of precut kits…it works fine for me. I cleaned with acetone prior to install on this brand new kayak. Had a couple of spot I had to use some extra adhesive(Marine Goop) to get it to stay down…3 small areas on this whole job. The adhesive does get wrinkled after laying flat from being rolled up….but doesn’t seem to affect the adhesion. Only been out twice and hosed it down afterwards. Been exposed to the Texas heat/sun about 12hrs and 100°+ garage for about 1 month. Looks like it will last.

I was was disappointed as to how thin the material in between the raised matting was. If a person is not REAL careful and accurately install it exactly where it is intended to be, then it will shred in an effort to reposition it. Additionally, putting it down and grooming all of the wrinkles and air bubbles out of it is a real challenge.I'm curious as to how well it will hold up as it is quite soft foam like matting. Another concern is as to whether or not it will mold/mildew/retain fish residue, etc.It is soft and comfortable to walk on and does provide a non-slip surface.

We re-floored our boat with this and it turned out amazing. People compliment us on it often. Great material.

Really easy to work with.. had to order two sheets.. at different times.. one came just a hair darker.. so if you need 2 or more sheets order at the same time.. maybe they'll come off the same roll..I was sticking it to an all aluminum deck that had been prepped and wiped down with mineral spirits, which seemed to help really make it stick.. rolled it out with the wife's rolling pin..Like I said, time will tell.. but I think it looks great!!If you're contemplating on buying this over another choice.. get this one.. I'd buy again

after one year the adhesive is peeling off the foam (it is still stuck well to the deck) and the foam is breaking down. it leaves grey dust on your feet when you walk on it.most of the time I had a cover on the boat so the actual days this product was in the weather was very small.however, when I contact the seller, they were very responsive and made it right for me.

It looked great when applied but within a few weeks the material has degraded to the point where touching it leaves a fine powder and if it's wet it will leech out and stain anything it touches. Does not hold up to UV exposure.

We originally got this in March 2020 for our golf cart flooring. I really didn't think it would stay long due to the heat in AZ but it is still on and even better cleans up great each time. Just wash it down and good as new. Hasn't lifted at all, even in corners. So, now we needed to replace the carpet on our outdoor steps & landing, both in the front and back. After putting it on, I did lay pavers on top overnight to ensure a good seal since steps and landing weren't perfectly flat in some areas. That was the beginning of April and so far so good. Back steps are in direct sunlight (heat 115ish in summer), so we'll see if they have issues then but I think they'll do as great as on the cart.

This flooring is so nice, thick, classic looking and really elevates the look of our old beloved Bayliner. It was so easy to trim to fit and put down, it sticks like heck and gives a real "wow" look immediately, to the point people keep stopping by the boat to ask what it is/where they can get it. It's tough and forgives our wild adventures including fishing, barbecuing, eating, drinking, spilling, laughing, dog paws, messy relatives, and leaving our wet shoes on because it's that kind of boat/life. We hose the flooring off, stains disappear and it dries and looks calm and classy again shortly after. And it was exponentially cheaper than boat shops/boat supply dealers. Recommend!

Glad we read the reviews. This is a Kingfisher Aluminum boat. We acetone and then windex’d the floor before applying. We also sprayed the 3mm adhesive down before putting the flooring down. The backing paper and adhesive is “ok”. The cut outs of the flooring aren’t square which wasn’t a big deal for us as we had plenty of extra.We outlined the position of each piece with painters tape. The. Used a large sheet of poly caper barrier to trace and outline the pieces. Took the Polly and put the foam flooring underneath it and cut it out. It took us about 4 nights to do all this but turned out great.The flooring is comfortable and durable. I have dragged coolers, fish, crab traps, and prawn traps across it. It never tore or lifted but we spent a lot of time carefully applying the flooring down. Our dog really liked it when we put this down as she has way more grip so do the kids.One of the only complaints I have is it’s hard to clean. If you have dirty shoes or even walk from the dock onto the boat and dirt gets on it it takes a bit of elbow grease to get everything cleaned. It doesn’t hold stains but does take a bit to scrub it. I never had problems with it lifting or bunking in the sun.I would use it again.

Feels and looks great but the adhesive backing sucks.. I installed this on a clean new fiberglass floor and as soon as it was washed for the first time the backing came free

good quality and easy install.

Over the years I have purchased some good and some bad ........ this hits the 'negative' STAR territory.Restoring older classis run-about and needed flooring ....... voila!Watched videos, checked the review .......... bought few rolls.1) Opened box and where the roll had been taped the foam was broken ....... thought 'no problem, I have to cut anyway'!2) So, I spent the day cutting templates and then cutting foam until ready to install.3) Youtube videos 'strongly' suggested using additional glue vs relying on the glued side of the foam. So, I purchased glue and followed process to glue an area, then placed foam. All went beautifully and placed weights around the edges. All seemed great!4) I continued and ~ 1/2 hour later .......... I noticed the flooring had begun to 'bubble'! Areas seemed to be pushing up and 'not' sticking. It was as if the foam was stretching ............. I pushed and rolled and .....5) I have now placed everything I have that had of any weight over the flooring and am 'praying' this will stick. My expectations, however, are that I will have an absolute mess and have to peel up the flooring with some areas having actually stuck ...... imagine!!Summary:The so-called 'sticky side' of this product ............ Scotch Tape is better!Cutting .......... extremely difficult to get a clean cut.Unrolling the product makes it appear that the paper backing was applied 'after' glue layer applied to the foam as bending it to 'lay' position is impossible and 'crinkles' the paper backing.I have worked hours and hours to restore this classic and this has set me back countless more hours.The 'Return' Policy is a wee bit tough to process at this point and a refund wouldn't even come close to compensating the mess this has caused.As you can guess, I would certainly not recommend this product!I would suggest Amazon dump this seller / product.Negative Star rating applies!